-- *****************************************************************
-- CISCO-DSPU-MIB.my: Cisco DSPU MIB
--
-- November 1994, Paul Pearce
--
-- Copyright (c) 1994-1995 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************CISCO-DSPU-MIB DEFINITIONS::=BEGIN-- MIB definitions for Cisco DownStream Physical Unit (DSPU) support
--
-- This MIB contains the information necessary
-- for the definition and management of DSPU objects.
--
-- The following DSPU objects are supported:
--
-- (1) dspuNode -> Global DSPU node information
--
-- (2) dspuPoolClass -> LU pool class information
--
-- (3) dspuPooledLu -> Pooled LU information
--
-- (4) dspuPu -> Upstream/Downstream PU node information
--
-- (5) dspuLu -> Upstream/Downstream LU information
--
-- (6) dspuSap -> Local SAP information
--
-- NOTE: Please reference the Router Products Configuration Guide
-- and/or the Router Products Command Reference for additional
-- information about DSPU configuration parameters
--IMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE,Counter32,Integer32FROM SNMPv2-SMI
DisplayString,MacAddress,TruthValue,TimeStamp,RowStatusFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ciscoMgmt
FROM CISCO-SMI;
-- ***************************************************************
-- Define dspu MIB object
-- ***************************************************************ciscoDspuMIB MODULE-IDENTITYLAST-UPDATED"9508150000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"DESCRIPTION"Used to define and manage DSPU objects."REVISION"9512180000Z"DESCRIPTION"Declare some Trap objects obsolete and create
new Trap Objects to permit Trap generation."REVISION"9508150000Z"DESCRIPTION"Specify a correct (non-negative) range for several
index objects."REVISION"9501250000Z"DESCRIPTION"Updated compliance/conformance information."::={ ciscoMgmt 24}
-- ***************************************************************
-- Define dspuObjects
-- ***************************************************************dspuObjects OBJECTIDENTIFIER::={ ciscoDspuMIB 1}dspuNode OBJECTIDENTIFIER::={ dspuObjects 1}dspuPoolClass OBJECTIDENTIFIER::={ dspuObjects 2}dspuPooledLu OBJECTIDENTIFIER::={ dspuObjects 3}dspuPu OBJECTIDENTIFIER::={ dspuObjects 4}dspuLu OBJECTIDENTIFIER::={ dspuObjects 5}dspuSap OBJECTIDENTIFIER::={ dspuObjects 6}
-- ***************************************************************
-- Define dspuNode object
-- ***************************************************************dspuNodeRsrb OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"RSRB feature enabled/disabled for the DSPU node.
TRUE -> RSRB feature enabled
FALSE -> RSRB feature disabled
If the RSRB feature is enabled, the following object
values must be valid (i.e. non-zero):
- dspuNodeRsrbLocalVirtualRing
- dspuNodeRsrbBridgeNumber
- dspuNodeRsrbTargetVirtualRing
- dspuNodeRsrbVirtualMacAddress"DEFVAL{ false }::={ dspuNode 1}dspuNodeRsrbLocalVirtualRing OBJECT-TYPESYNTAXINTEGER(0..4096)MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"Local virtual ring number used by the DSPU node.
LocalVirtualRing is zero if RSRB is not enabled."::={ dspuNode 2}dspuNodeRsrbBridgeNumber OBJECT-TYPESYNTAXINTEGER(0..15)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Bridge number connecting the DSPU LocalVirtualRing
with the RSRB TargetVirtualRing.
Currently, the only valid BridgeNumber supported is 1.
BridgeNumber must be one if RSRB is enabled.
BridgeNumber is zero if RSRB is not enabled."::={ dspuNode 3}dspuNodeRsrbTargetVirtualRing OBJECT-TYPESYNTAXINTEGER(0..4096)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION
"Target virtual ring number used for RSRB.
TargetVirtualRing is zero if RSRB is not enabled."::={ dspuNode 4}dspuNodeRsrbVirtualMacAddress OBJECT-TYPESYNTAXMacAddressMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Virtual MAC address of the the DSPU node.
VirtualMacAddress is zero if RSRB is not enabled."::={ dspuNode 5}dspuNodeDefaultPu OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Default-PU feature enabled/disabled for the DSPU node.
TRUE -> Default-PU feature enabled
FALSE -> Default-PU feature disabled"DEFVAL{ false }::={ dspuNode 6}dspuNodeDefaultPuWindowSize OBJECT-TYPE
SYNTAXINTEGER(1..127)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Send/receive window size to be used across the link
between the default-PU and a remote PU."DEFVAL{7}::={ dspuNode 7}dspuNodeDefaultPuMaxIframe OBJECT-TYPESYNTAXINTEGER(64..18432)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Maximum size of an I-frame that can be transmitted/received
across the link between the default-PU and a remote PU."DEFVAL{1472}::={ dspuNode 8}
dspuNodeActivationWindow OBJECT-TYPESYNTAXINTEGER(1..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Activation pacing window used by the DSPU node to limit
the number of activation RUs sent for a given SAP before
waiting for responses from the remote."DEFVAL{10}::={ dspuNode 9}dspuNodeLastConfigChgTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Timestamp of last change to DSPU configuration parameters.
LastConfigChgTime reflects any change in DSPU configuration."::={ dspuNode 10}-- ***************************************************************
-- Define dspuPoolClass object
-- ***************************************************************--
-- Define dspuPoolClassTable
--dspuPoolClassTable OBJECT-TYPESYNTAXSEQUENCEOF DspuPoolClassEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing defined pool classes for the DSPU node.
A pool class is defined at the DSPU node as a pool
of upstream LUs that may be shared among downstream PUs.
Each entry in the table represents a separate
pool class definition.
Entries in the table may not be created/deleted;
however, values in existing entries may be modified.
Pool classes are created when an existing LU is
defined as a member of the pool class."::={ dspuPoolClass 1}dspuPoolClassEntry OBJECT-TYPESYNTAX DspuPoolClassEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents a defined pool class."INDEX{ dspuPoolClassIndex }
::={ dspuPoolClassTable 1}
DspuPoolClassEntry ::=SEQUENCE{
dspuPoolClassIndex
Integer32(0..2147483647),
dspuPoolClassName
DisplayString,
dspuPoolClassInactivityTimeout
INTEGER,
dspuPoolClassOperUpStreamLuDefs
Integer32,
dspuPoolClassOperDnStreamLuDefs
Integer32}dspuPoolClassIndex OBJECT-TYPESYNTAXInteger32(0..2147483647)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Index of a pool class entry in the dspuPoolClassTable."::={ dspuPoolClassEntry 1}dspuPoolClassName OBJECT-TYPE
SYNTAXDisplayString(SIZE(0..10))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Name identifier of the pool class."::={ dspuPoolClassEntry 2}dspuPoolClassInactivityTimeout OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Value (in minutes) of the inactivity timeout that
will be applied to active LU sessions assigned
from the pool class.
The inactivity timeout feature for pooled LUs is
disabled if the InactivityTimeout value is zero."DEFVAL{0}::={ dspuPoolClassEntry 3}
dspuPoolClassOperUpStreamLuDefs OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of upstream LUs defined in the pool class."::={ dspuPoolClassEntry 4}dspuPoolClassOperDnStreamLuDefs OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of downstream LUs defined in the pool class."::={ dspuPoolClassEntry 5}-- ***************************************************************
-- Define dspuPooledLu object
-- ***************************************************************--
-- Define dspuPooledLuTable
--dspuPooledLuTable OBJECT-TYPESYNTAXSEQUENCEOF DspuPooledLuEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Table listing all LUs defined in a specified pool class.
The entries in the table provide information such that
the downstream LUs in the pool can be correlated with
the upstream LUs to which they may be assigned
and vice versa.
If all upstream LUs have been assigned,
downstream LUs may be waiting for assignment.
If there are no downstream LUs waiting for assignment,
upstream LUs may be unassigned."::={ dspuPooledLu 1}dspuPooledLuEntry OBJECT-TYPESYNTAX DspuPooledLuEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an LU that is defined
as a member of the specified pool class."INDEX{ dspuPoolClassIndex,
dspuPuOperIndex,
dspuLuOperLuLocalAddress }::={ dspuPooledLuTable 1}
DspuPooledLuEntry ::=SEQUENCE{
dspuPooledLuPeerPuIndex
Integer32,
dspuPooledLuPeerLuLocalAddress
INTEGER}dspuPooledLuPeerPuIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Index (dspuPuOperIndex) of the peer PU that owns
the peer LU.
PeerPuIndex is zero if peer LU has not been assigned."::={ dspuPooledLuEntry 1}dspuPooledLuPeerLuLocalAddress OBJECT-TYPESYNTAXINTEGER(0..254)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"NAU address (dspuLuOperLuLocalAddress) of the peer LU.
PeerLuLocalAddress is zero if peer LU has not been assigned."::={ dspuPooledLuEntry 2}
-- ***************************************************************
-- Define dspuPu object
-- ***************************************************************--
-- Define dspuPuAdminTable
--dspuPuAdminTable OBJECT-TYPESYNTAXSEQUENCEOF DspuPuAdminEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing all defined upstream/downstream PUs
that are owned by the DSPU node.
NOTE: The dspuPuAdminTable does not include default
downstream PUs that may be dynamically created."::={ dspuPu 1}dspuPuAdminEntry OBJECT-TYPESYNTAX DspuPuAdminEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents a defined upstream/downstream PU."INDEX{ dspuPuAdminIndex }::={ dspuPuAdminTable 1}
DspuPuAdminEntry ::=SEQUENCE{
dspuPuAdminIndex
Integer32(0..2147483647),
dspuPuAdminName
DisplayString,
dspuPuAdminType
INTEGER,
dspuPuAdminRemoteMacAddress
MacAddress,
dspuPuAdminRemoteSapAddress
INTEGER,
dspuPuAdminLocalSapAddress
INTEGER,
dspuPuAdminXid
Integer32,
dspuPuAdminXidFmt
INTEGER,
dspuPuAdminWindowSize
INTEGER,
dspuPuAdminMaxIframe
INTEGER,
dspuPuAdminLinkRetryCount
INTEGER,
dspuPuAdminLinkRetryTimeout
INTEGER,
dspuPuAdminStartPu
TruthValue,
dspuPuAdminDlcType
INTEGER,
dspuPuAdminDlcUnit
INTEGER,
dspuPuAdminDlcPort
INTEGER,
dspuPuAdminFocalPoint
TruthValue,
dspuPuAdminRowStatus
RowStatus,
dspuPuAdminRemoteAddress
DisplayString}dspuPuAdminIndex OBJECT-TYPESYNTAXInteger32(0..2147483647)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Index of the PU entry in the dspuPuAdminTable."::={ dspuPuAdminEntry 1}dspuPuAdminName OBJECT-TYPESYNTAXDisplayString(SIZE(0..8))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Name of the PU."::={ dspuPuAdminEntry 2}
dspuPuAdminType OBJECT-TYPESYNTAXINTEGER{upstreamPu (1),dnstreamPu (2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"PU Type is either upstream or downstream."::={ dspuPuAdminEntry 3}dspuPuAdminRemoteMacAddress OBJECT-TYPESYNTAXMacAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"MAC address of the remote PU."::={ dspuPuAdminEntry 4}dspuPuAdminRemoteSapAddress OBJECT-TYPESYNTAXINTEGER(1..254)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"SAP address of the remote PU."DEFVAL{4}::={ dspuPuAdminEntry 5}dspuPuAdminLocalSapAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"SAP address of the local PU."DEFVAL{8}::={ dspuPuAdminEntry 6}dspuPuAdminXid OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION
"Upstream PU : XID that will be sent to the remote PU.
Dnstream PU : XID that must be received from the remote PU."::={ dspuPuAdminEntry 7}dspuPuAdminXidFmt OBJECT-TYPESYNTAXINTEGER{formatUnknown (1),format0 (2),format3 (3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Type of XID format used during activation of the link
between this dspuNode and the remote PU."DEFVAL{ format3 }::={ dspuPuAdminEntry 8}dspuPuAdminWindowSize OBJECT-TYPESYNTAXINTEGER(1..127)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Send/Receive window size to be used across the link
between this dspuNode and the remote PU."DEFVAL{7}::={ dspuPuAdminEntry 9}dspuPuAdminMaxIframe OBJECT-TYPESYNTAXINTEGER(64..18432)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Maximum size of an I-frame that can be transmitted/received
across the link between this dspuNode and the remote PU."DEFVAL{1472}::={ dspuPuAdminEntry 10}dspuPuAdminLinkRetryCount OBJECT-TYPESYNTAXINTEGER(0..255)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Number of times that the DSPU node will attempt to activate
the link between the dspuNode and the remote PU."DEFVAL{4}::={ dspuPuAdminEntry 11}dspuPuAdminLinkRetryTimeout OBJECT-TYPESYNTAXINTEGER(1..600)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Value (in seconds) for the delay between link activation
attempts between the dspuNode and the remote PU."DEFVAL{30}::={ dspuPuAdminEntry 12}dspuPuAdminStartPu OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-create
STATUScurrentDESCRIPTION"Attempt link activation with the remote PU.
TRUE -> Attempt link activation with remote PU.
FALSE -> Do not attempt link activation with remote PU."DEFVAL{ false }::={ dspuPuAdminEntry 13}dspuPuAdminDlcType OBJECT-TYPESYNTAXINTEGER{undefined (1),sdlc (2),ethernet (5),tokenRing (6),rsrb (8),framerelay (9),fddi (10),qllc (11)
}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"DLC type used by the dspuNode for link activation
with the remote PU."::={ dspuPuAdminEntry 14}dspuPuAdminDlcUnit OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"DLC unit used by the dspuNode for link activation
with the remote PU."::={ dspuPuAdminEntry 15}dspuPuAdminDlcPort OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION
"DLC port used by the dspuNode for link activation
with the remote PU."::={ dspuPuAdminEntry 16}dspuPuAdminFocalPoint OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"PU serves as a focal point for alert forwarding.
TRUE -> PU serves as focal point
FALSE -> PU does not serve as focal point
Only an upstream PU may be defined as a focal point.
Downstream PUs can never be defined as a focal point;
FocalPoint is always FALSE for downstream PUs.
The DSPU node may define only one upstream PU as
a focal point PU."DEFVAL{ false }::={ dspuPuAdminEntry 17}dspuPuAdminRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION
"Used by a Management Station to create or delete the row
entry in the dspuPuAdminTable following the RowStatus
textual convention.
Upon successful creation of the row, an Agent automatically
creates a corresponding entry in the dspuPuOperTable.
The Management Station can set the value to 'destroy (6)'
and the Agent will then delete the rows corresponding
to this PU from the dspuPuAdminTable and dspuPuOperTable."::={ dspuPuAdminEntry 18}dspuPuAdminRemoteAddress OBJECT-TYPESYNTAXDisplayString(SIZE(0..20))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Poll address, DLCI, or subscriber address
associated with the remote PU."::={ dspuPuAdminEntry 19}--
-- Define dspuPuOperTable
--dspuPuOperTable OBJECT-TYPESYNTAXSEQUENCEOF DspuPuOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing all active upstream/downstream PUs
that are owned by the DSPU node (including default PUs).
NOTE: In addition to the explicitly defined PUs from
the dspuPuAdminTable, the dspuPuOperTable also includes
default downstream PUs that may be dynamically created."::={ dspuPu 2}dspuPuOperEntry OBJECT-TYPESYNTAX DspuPuOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an active upstream/downstream PU."INDEX{ dspuPuOperIndex }::={ dspuPuOperTable 1}
DspuPuOperEntry ::=SEQUENCE{
dspuPuOperIndex
Integer32(0..2147483647),
dspuPuOperName
DisplayString,
dspuPuOperType
INTEGER,
dspuPuOperRemoteMacAddress
MacAddress,
dspuPuOperRemoteSapAddress
INTEGER,
dspuPuOperLocalSapAddress
INTEGER,
dspuPuOperXid
Integer32,
dspuPuOperXidFmt
INTEGER,
dspuPuOperWindowSize
INTEGER,
dspuPuOperMaxIframe
INTEGER,
dspuPuOperLinkRetryCount
INTEGER,
dspuPuOperLinkRetryTimeout
INTEGER,
dspuPuOperStartPu
TruthValue,
dspuPuOperDlcType
INTEGER,
dspuPuOperDlcUnit
INTEGER,
dspuPuOperDlcPort
INTEGER,
dspuPuOperFocalPoint
TruthValue,
dspuPuOperState
INTEGER,
dspuPuOperFsmState
INTEGER,
dspuPuOperStartTime
TimeStamp,
dspuPuOperLastStateChgTime
TimeStamp,
dspuPuOperRemoteAddress
DisplayString}dspuPuOperIndex OBJECT-TYPESYNTAXInteger32(0..2147483647)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Index of the PU entry in dspuPuOperTable."::={ dspuPuOperEntry 1}dspuPuOperName OBJECT-TYPESYNTAXDisplayString(SIZE(0..8))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Name of the PU."::={ dspuPuOperEntry 2}
dspuPuOperType OBJECT-TYPESYNTAXINTEGER{upstreamPu (1),dnstreamPu (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"PU type is either upstream or downstream."::={ dspuPuOperEntry 3}dspuPuOperRemoteMacAddress OBJECT-TYPESYNTAXMacAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"MAC address of the remote PU."::={ dspuPuOperEntry 4}dspuPuOperRemoteSapAddress OBJECT-TYPESYNTAXINTEGER(1..254)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"SAP address of the remote PU."DEFVAL{4}::={ dspuPuOperEntry 5}dspuPuOperLocalSapAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"SAP address of the local PU."DEFVAL{8}::={ dspuPuOperEntry 6}dspuPuOperXid OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Upstream PU : XID that was sent to the remote PU.
Dnstream PU : XID that was received from the remote PU."::={ dspuPuOperEntry 7}dspuPuOperXidFmt OBJECT-TYPESYNTAXINTEGER{formatUnknown (1),format0 (2),format3 (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Type of XID format used during activation of the link
between this dspuNode and the remote PU."::={ dspuPuOperEntry 8}dspuPuOperWindowSize OBJECT-TYPESYNTAXINTEGER(1..127)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Send/Receive window size to be used across the link
between this dspuNode and the remote PU."DEFVAL{7}::={ dspuPuOperEntry 9}dspuPuOperMaxIframe OBJECT-TYPESYNTAXINTEGER(64..18432)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Maximum size of an I-frame that can be transmitted/received
across the link between this dspuNode and the remote PU."DEFVAL{1472}::={ dspuPuOperEntry 10}dspuPuOperLinkRetryCount OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Number of times that the DSPU node will attempt to activate
the link between the dspuNode and the remote PU."DEFVAL{4}::={ dspuPuOperEntry 11}dspuPuOperLinkRetryTimeout OBJECT-TYPESYNTAXINTEGER(1..600)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Value (in seconds) for the delay between link activation
attempts between the dspuNode and the remote PU."DEFVAL{30}::={ dspuPuOperEntry 12}dspuPuOperStartPu OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Attempt link activation with the remote PU.
TRUE -> Attempt link activation with remote PU.
FALSE -> Do not attempt link activation with remote PU."DEFVAL{ false }::={ dspuPuOperEntry 13}dspuPuOperDlcType OBJECT-TYPESYNTAXINTEGER{undefined (1),sdlc (2),ethernet (5),tokenRing (6),rsrb (8),framerelay (9),fddi (10),qllc (11)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"DLC type used by the dspuNode for link activation
with the remote PU."::={ dspuPuOperEntry 14}dspuPuOperDlcUnit OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"DLC unit used by the dspuNode for link activation
with the remote PU."::={ dspuPuOperEntry 15}dspuPuOperDlcPort OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"DLC port used by the dspuNode for link activation
with the remote PU."
::={ dspuPuOperEntry 16}dspuPuOperFocalPoint OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"PU serves as a focal point for alert forwarding.
TRUE -> PU serves as focal point
FALSE -> PU does not serve as focal point
Only an upstream PU may be defined as a focal point.
Downstream PUs can never be defined as a focal point;
FocalPoint is always FALSE for downstream PUs.
The DSPU node may define only one upstream PU as
a focal point PU."DEFVAL{ false }::={ dspuPuOperEntry 17}dspuPuOperState OBJECT-TYPESYNTAXINTEGER{active (1),inactive (2)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Operational state of PU is either active or inactive."::={ dspuPuOperEntry 18}dspuPuOperFsmState OBJECT-TYPESYNTAXINTEGER{linkReset (1),linkPendConnOut (2),linkPendConnIn (3),linkPendXid (4),linkXidNeg (5),linkConnOut (6),linkConnIn (7),linkConnected (8),puPendAct (9),puActive (10),
puBusy (11),puPendInact (12),linkPendDisc (13),linkPendClose (14)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Current FSM state of the PU as follows:
linkReset
- Link is in reset state - not connected
linkPendConnOut
- Pending ConnectOut to establish link
linkPendConnIn
- Pending ConnectIn to establish link
linkPendXid
- Pending XID negotiation on the link
linkXidNeg
- XID negotiation proceeding on link
linkConnOut
- ConnectOut link activation
linkConnIn
- ConnectIn link activation
linkConnected
- Link connected, PU inactive
puPendAct
- Link connected, PU pending activation
puActive
- Link connected, PU active
puBusy
- Link connected, PU busy
puPendInact
- Link connected, PU pending deactivation
linkPendDisc
- Pending disconnect of link
linkPendClose
- Pending close of link station"::={ dspuPuOperEntry 19}dspuPuOperStartTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Timestamp of PU activation (when ACTPU +rsp received)."::={ dspuPuOperEntry 20}dspuPuOperLastStateChgTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"TimeStamp of last PU state change between active<->inactive."::={ dspuPuOperEntry 21}dspuPuOperRemoteAddress OBJECT-TYPE
SYNTAXDisplayString(SIZE(0..20))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Poll address, DLCI, or subscriber address
associated with the remote PU."::={ dspuPuOperEntry 22}-- ***************************************************************
-- Define dspuPuStats object
-- ***************************************************************--
-- Define dspuPuStatsTable
--dspuPuStatsTable OBJECT-TYPESYNTAXSEQUENCEOF DspuPuStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing the statistics recorded for each PU."::={ dspuPu 3}dspuPuStatsEntry OBJECT-TYPESYNTAX DspuPuStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an active upstream/downstream PU
and has a corresponding entry in the dspuPuOperTable."INDEX{ dspuPuOperIndex }::={ dspuPuStatsTable 1}
DspuPuStatsEntry ::=SEQUENCE{
dspuPuStatsSentBytes
Counter32,
dspuPuStatsRcvdBytes
Counter32,
dspuPuStatsSentFrames
Counter32,
dspuPuStatsRcvdFrames
Counter32,
dspuPuStatsSentNegativeRsps
Counter32,
dspuPuStatsRcvdNegativeRsps
Counter32,
dspuPuStatsActiveLus
Counter32,
dspuPuStatsInactiveLus
Counter32,
dspuPuStatsBindLus
Counter32,
dspuPuStatsActivationFailures
Counter32,
dspuPuStatsLastActivationFailureReason
INTEGER}dspuPuStatsSentBytes OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of bytes sent by this PU."::={ dspuPuStatsEntry 1}dspuPuStatsRcvdBytes OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of bytes received by this PU."::={ dspuPuStatsEntry 2}dspuPuStatsSentFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of frames sent by this PU."
::={ dspuPuStatsEntry 3}dspuPuStatsRcvdFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of frames received by this PU."::={ dspuPuStatsEntry 4}dspuPuStatsSentNegativeRsps OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of negative responses sent by this PU."::={ dspuPuStatsEntry 5}dspuPuStatsRcvdNegativeRsps OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of negative responses received by this PU."::={ dspuPuStatsEntry 6}
dspuPuStatsActiveLus OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of active LUs on this PU
(LU becomes active when ACTLU +rsp received)."::={ dspuPuStatsEntry 7}dspuPuStatsInactiveLus OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of inactive LUs on this PU
(LU is inactive until ACTLU rq or ACTLU +rsp received)."::={ dspuPuStatsEntry 8}dspuPuStatsBindLus OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of LUs on this PU which are active-in-session.
(LU is active-in-session when BIND rq received)"::={ dspuPuStatsEntry 9}dspuPuStatsActivationFailures OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of activation failures for this PU."::={ dspuPuStatsEntry 10}dspuPuStatsLastActivationFailureReason OBJECT-TYPESYNTAXINTEGER{noError (1),otherError (2),internalError (3),configurationError (4),puNegativeResponse (5),puAlreadyActive (6)
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reason for last activation failure of this PU as follows:
noError
- No PU activation failure has been detected
otherError
- Undefined error detected during PU activation
internalError
- Internal resources error detected during PU activation
configurationError
- PU configuration error - PU could not be activated
puNegativeResponse
- Negative ACTPU response received from remote PU
puAlreadyActive
- PU is already active"::={ dspuPuStatsEntry 11}--
-- Cannot "legally" change the OID for MIB variables.
-- Instead, create new MIB variables with different OIDs.
--dspuPuTraps OBJECTIDENTIFIER::={ dspuPu 4}dspuPuStateChangeTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuPuOperState }
STATUSobsoleteDESCRIPTION"Generated when the operational state
of the PU changes between active<-->inactive.
The following information is returned:
dspuPuOperName -> PU name
dspuPuOperState -> Current operational state of the PU"::={ dspuPuTraps 1}dspuPuActivationFailureTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuPuOperState,
dspuPuStatsLastActivationFailureReason }STATUSobsoleteDESCRIPTION"Generated whenever a PU activation failure is detected.
The following information is returned:
dspuPuOperName
-> PU name
dspuPuOperState
-> Current operational state of the PU
dspuPuStatsLastActivationFailureReason
-> Reason for PU activation failure"::={ dspuPuTraps 2}dspuPuTrapsPrefix OBJECTIDENTIFIER::={ dspuPuTraps 0}
newdspuPuStateChangeTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuPuOperState }STATUScurrentDESCRIPTION"Generated when the operational state
of the PU changes between active<-->inactive.
The following information is returned:
dspuPuOperName -> PU name
dspuPuOperState -> Current operational state of the PU"::={ dspuPuTrapsPrefix 1}newdspuPuActivationFailureTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuPuOperState,
dspuPuStatsLastActivationFailureReason }STATUScurrentDESCRIPTION"Generated whenever a PU activation failure is detected.
The following information is returned:
dspuPuOperName
-> PU name
dspuPuOperState
-> Current operational state of the PU
dspuPuStatsLastActivationFailureReason
-> Reason for PU activation failure"::={ dspuPuTrapsPrefix 2}-- ***************************************************************
-- Define dspuLu object
-- ***************************************************************--
-- Define dspuLuAdminTable
--dspuLuAdminTable OBJECT-TYPESYNTAXSEQUENCEOF DspuLuAdminEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing all LUs owned by the PU.
NOTE: The dspuLuAdminTable does not include LUs owned by
default downstream PUs that may be dynamically created."::={ dspuLu 1}dspuLuAdminEntry OBJECT-TYPESYNTAX DspuLuAdminEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents a defined LU owned by the PU."
INDEX{ dspuPuAdminIndex, dspuLuAdminLuLocalAddress }::={ dspuLuAdminTable 1}
DspuLuAdminEntry ::=SEQUENCE{
dspuLuAdminLuLocalAddress
INTEGER,
dspuLuAdminType
INTEGER,
dspuLuAdminPoolClassName
DisplayString,
dspuLuAdminPeerPuIndex
Integer32,
dspuLuAdminPeerLuLocalAddress
INTEGER,
dspuLuAdminRowStatus
RowStatus}dspuLuAdminLuLocalAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"NAU address of the local LU."::={ dspuLuAdminEntry 1}
dspuLuAdminType OBJECT-TYPESYNTAXINTEGER{pooled(1),dedicated(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"LU type is either pooled or dedicated."::={ dspuLuAdminEntry 2}dspuLuAdminPoolClassName OBJECT-TYPESYNTAXDisplayString(SIZE(0..10))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Pool class to which the LU is defined as a member.
The dspuLuAdminPoolClassName is valid for pooled LUs only."::={ dspuLuAdminEntry 3}dspuLuAdminPeerPuIndex OBJECT-TYPE
SYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"For downstream LUs, the PeerPuIndex identifies
the upstream PU that owns the upstream LU to
which this downstream LU is assigned.
For upstream LUs, the PeerPuIndex identifies
the downstream PU that owns the downstream LU
to which this upstream LU is assigned.
The PeerPuIndex is valid for dedicated LUs only;
otherwise, the PeerPuIndex is zero."::={ dspuLuAdminEntry 4}dspuLuAdminPeerLuLocalAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"For downstream LUs, the PeerLuLocalAddress identifies
the NAU address of the upstream LU to which this
downstream LU is assigned.
For upstream LUs, the PeerLuLocalAddress identifies
the NAU address of the downstream LU to which this
upstream LU is assigned.
The PeerLuLocalAddress is valid for dedicated LUs only;
otherwise, the PeerLuLocalAddress is zero."::={ dspuLuAdminEntry 5}dspuLuAdminRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Used by a Management Station to create or delete the row
entry in the dspuLuAdminTable following the RowStatus
textual convention.
Upon successful creation of the row, an Agent automatically
creates a corresponding entry in the dspuLuOperTable.
The Management Station can set the value to 'destroy (6)'
and the Agent will then delete the rows corresponding to
this LU from the dspuLuAdminTable and the dspuLuOperTable."::={ dspuLuAdminEntry 6}--
-- Define dspuLuOperTable
--dspuLuOperTable OBJECT-TYPESYNTAXSEQUENCEOF DspuLuOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing all LUs owned by the PU.
NOTE: In addition to the LUs owned by explicitly defined PUs
from the dspuLuAdminTable, the dspuLuOperTable also
includes the LUs owned by default downstream PUs
that may be dynamically created."::={ dspuLu 2}dspuLuOperEntry OBJECT-TYPESYNTAX DspuLuOperEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents a defined LU owned by the PU."INDEX{ dspuPuOperIndex, dspuLuOperLuLocalAddress }::={ dspuLuOperTable 1}
DspuLuOperEntry ::=SEQUENCE{
dspuLuOperLuLocalAddress
INTEGER,
dspuLuOperType
INTEGER,
dspuLuOperPoolClassName
DisplayString,
dspuLuOperPeerPuIndex
Integer32,
dspuLuOperPeerLuLocalAddress
INTEGER,
dspuLuOperState
INTEGER,
dspuLuOperFsmState
INTEGER,
dspuLuOperSessionState
INTEGER,
dspuLuOperLastActivationFailureReason
INTEGER}dspuLuOperLuLocalAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"NAU address of the local LU."::={ dspuLuOperEntry 1}dspuLuOperType OBJECT-TYPESYNTAXINTEGER{pooled(1),
dedicated(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"LU type is either pooled or dedicated."::={ dspuLuOperEntry 2}dspuLuOperPoolClassName OBJECT-TYPESYNTAXDisplayString(SIZE(0..10))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Pool class to which the LU is defined as a member.
The dspuLuOperPoolClassName is valid for pooled LUs only."::={ dspuLuOperEntry 3}dspuLuOperPeerPuIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"For downstream LUs, the PeerPuIndex identifies
the upstream PU that owns the upstream LU to
which this downstream LU is assigned.
For upstream LUs, the PeerPuIndex identifies
the downstream PU that owns the downstream LU
to which this upstream LU is assigned.
If PeerPuIndex is zero, the LU is a pooled LU and has
not been assigned a peer LU from the pool."::={ dspuLuOperEntry 4}dspuLuOperPeerLuLocalAddress OBJECT-TYPESYNTAXINTEGER(0..254)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"For downstream LUs, the PeerLuLocalAddress identifies
the NAU address of the upstream LU to which this
downstream LU is assigned.
For upstream LUs, the PeerLuLocalAddress identifies
the NAU address of the downstream LU to which this
upstream LU is assigned.
If the PeerLuLocalAddress is zero, the LU is a pooled LU
and has not been assigned a peer LU from the pool."
::={ dspuLuOperEntry 5}dspuLuOperState OBJECT-TYPESYNTAXINTEGER{active (1),inactive (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Operational state of LU is either active or inactive."::={ dspuLuOperEntry 6}dspuLuOperFsmState OBJECT-TYPESYNTAXINTEGER{reset(1),dnLuStarted(2),upLuActive(3),dnLuPendAct(4),dnLuActUnav(5),
upLuPendAvail(6),bothAvail(7),dnLuPendInact(8),upLuPendInact(9),luInactivityTimeout(10),dnInactivityPendInact(11)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Current FSM state of the LU as follows:
reset
- neither dnLu or upLu active
dnLuStarted
- dnLu active, upLu inactive
upLuActive
- upLu active, dnLu inactive
dnLuPendAct
- dnLu pending activation, upLu active-unavailable
dnLuActUnav
- dnLu active-unavailable, upLu active-available
upLuPendAvail
- upLu pending-available
bothAvail
- both upLu and dnLu active-available
dnLuPendInact
- dnLu pending inactive
upLuPendInact
- upLu pending inactive
luInactivityTimeout
- inactivity Timeout on LU-to-LU session
dnInactivityPendInact
- dnLu pending inactive from inactivity timeout"::={ dspuLuOperEntry 7}dspuLuOperSessionState OBJECT-TYPESYNTAXINTEGER{bound (1),unbound (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Operational state of LU session is either bound or unbound."::={ dspuLuOperEntry 8}dspuLuOperLastActivationFailureReason OBJECT-TYPESYNTAXINTEGER{noError (1),
otherError (2),luNegativeResponse (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reason for last activation failure of this PU as follows:
noError
- No LU activation failure has been detected
otherError
- Undefined error detected during LU activation
luNegativeResponse
- Negative ACTLU response received from remote LU"::={ dspuLuOperEntry 9}--
-- Cannot "legally" change the OID for MIB variables.
-- Instead, create new MIB variables with different OIDs.
--dspuLuTraps OBJECTIDENTIFIER::={ dspuLu 3}dspuLuStateChangeTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuLuOperLuLocalAddress,
dspuLuOperState }
STATUSobsoleteDESCRIPTION"Generated when the operational state
of the PU changes between active<-->inactive.
The following information is returned:
dspuPuOperName
-> PU name
dspuLuOperLuLocalAddress
-> NAU address of LU
dspuLuOperState
-> Current operational state of the LU"::={ dspuLuTraps 1}dspuLuTrapsPrefix OBJECTIDENTIFIER::={ dspuLuTraps 0}newdspuLuStateChangeTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuLuOperState }STATUScurrentDESCRIPTION"Generated when the operational state
of the LU changes between active<-->inactive.
The following information is returned:
dspuPuOperName
-> PU name
dspuLuOperState
-> Current operational state of the LU"::={ dspuLuTrapsPrefix 1}
dspuLuActivationFailureTrap NOTIFICATION-TYPEOBJECTS{ dspuPuOperName,
dspuLuOperState,
dspuLuOperLastActivationFailureReason }STATUScurrentDESCRIPTION"Generated whenever an LU activation failure is detected.
The following information is returned:
dspuPuOperName
-> PU name
dspuLuOperState
-> Current operational state of the LU
dspuLuOperLastActivationFailureReason
-> Reason for LU activation failure"::={ dspuLuTrapsPrefix 2}-- ***************************************************************
-- Define dspuSap object
-- ***************************************************************--
-- Define dspuSapTable
--dspuSapTable OBJECT-TYPESYNTAXSEQUENCEOF DspuSapEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Table listing the SAPs that are enabled for the DSPU node."::={ dspuSap 1}dspuSapEntry OBJECT-TYPESYNTAX DspuSapEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an enabled SAP for the DSPU node."INDEX{ dspuSapDlcType, dspuSapDlcUnit,
dspuSapDlcPort, dspuSapAddress }::={ dspuSapTable 1}
DspuSapEntry ::=SEQUENCE{
dspuSapAddress
INTEGER,
dspuSapType
INTEGER,
dspuSapDlcType
INTEGER,
dspuSapDlcUnit
INTEGER,
dspuSapDlcPort
INTEGER,
dspuSapOperState
INTEGER,
dspuSapRowStatus
RowStatus}dspuSapAddress OBJECT-TYPESYNTAXINTEGER(1..254)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"SAP address of the local SAP."::={ dspuSapEntry 1}dspuSapType OBJECT-TYPESYNTAXINTEGER{upstreamSap (1),dnstreamSap (2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Local SAP type is either upstreamSap or downstreamSap."::={ dspuSapEntry 2}dspuSapDlcType OBJECT-TYPE
SYNTAXINTEGER{undefined (1),sdlc (2),ethernet (5),tokenRing (6),rsrb (8),framerelay (9),fddi (10),qllc (11)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"DLC type of the adapter that owns the local SAP."::={ dspuSapEntry 3}dspuSapDlcUnit OBJECT-TYPESYNTAXINTEGER(0..255)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"DLC unit of the adapter that owns the local SAP."::={ dspuSapEntry 4}dspuSapDlcPort OBJECT-TYPESYNTAXINTEGER(0..255)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"DLC port of the adapter that owns the local SAP."::={ dspuSapEntry 5}dspuSapOperState OBJECT-TYPESYNTAXINTEGER{sapClosed (1),sapOpening (2),sapOpened (3),
sapClosing (4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Operational state of the local SAP as follows:
- sapClosed
- sapOpening
- sapOpened
- sapClosing"::={ dspuSapEntry 6}dspuSapRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used by a Management Station to create
or delete the row entry in the dspuSapTable following
the RowStatus textual convention.
The Management Station can set the value to 'destroy (6)'
and the Agent will then delete the rows corresponding to
this SAP from the dspuSapTable.
The local SAP address is enabled on the specified adapter
when a row entry in the dspuSapTable is created."::={ dspuSapEntry 7}
dspuSapTraps OBJECTIDENTIFIER::={ dspuSap 2}dspuSapStateChangeTrap NOTIFICATION-TYPEOBJECTS{ dspuSapDlcType,
dspuSapDlcUnit,
dspuSapDlcPort,
dspuSapAddress,
dspuSapOperState }STATUSobsoleteDESCRIPTION"Generated when the operational state of the SAP changes
between 'open' or 'closed'.
The following information is returned:
dspuSapOperDlcType
-> DLC type of the adapter on which SAP is located
dspuSapOperDlcUnit
-> Unit ID of the adapter on which SAP is located
dspuSapOperDlcPort
-> Port ID of the adapter on which SAP is located
dspuSapOperAddress
-> SAP address
dspuSapOperState
-> Current operational state of the SAP"::={ dspuSapTraps 1}-- ***************************************************************
-- Conformance information
-- ***************************************************************ciscoDspuMIBConformance OBJECTIDENTIFIER::={ ciscoDspuMIB 2}ciscoDspuMIBCompliances OBJECTIDENTIFIER::={ ciscoDspuMIBConformance 1}ciscoDspuMIBGroups OBJECTIDENTIFIER::={ ciscoDspuMIBConformance 2}-- Compliance statementsciscoDspuMIBCompliance MODULE-COMPLIANCESTATUSobsolete-- superseded by ciscoDspuMIBComplianceV11R01DESCRIPTION"The compliance statement for the SNMPv2 entities
which implement the Cisco DSPU MIB."MODULE-- this moduleMANDATORY-GROUPS{ dspuNodeGroup,
dspuPoolClassGroup,
dspuPooledLuGroup,
dspuPuGroup,
dspuLuGroup,
dspuSapGroup }::={ciscoDspuMIBCompliances 1}ciscoDspuMIBComplianceV11R01 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for the SNMPv2 entities
which implement the Cisco DSPU MIB."MODULE-- this moduleMANDATORY-GROUPS{ dspuNodeGroup,
dspuPoolClassGroup,
dspuPooledLuGroup,
dspuPuGroupV11R01,
dspuLuGroupV11R01,
dspuSapGroup }::={ciscoDspuMIBCompliances 2}-- Units of conformancedspuNodeGroup OBJECT-GROUPOBJECTS{ dspuNodeRsrb,
dspuNodeRsrbLocalVirtualRing,
dspuNodeRsrbBridgeNumber,
dspuNodeRsrbTargetVirtualRing,
dspuNodeRsrbVirtualMacAddress,
dspuNodeDefaultPu,
dspuNodeDefaultPuWindowSize,
dspuNodeDefaultPuMaxIframe,
dspuNodeActivationWindow,
dspuNodeLastConfigChgTime
}STATUScurrentDESCRIPTION"Global DSPU node information"::={ ciscoDspuMIBGroups 1}dspuPoolClassGroup OBJECT-GROUPOBJECTS{ dspuPoolClassName,
dspuPoolClassInactivityTimeout,
dspuPoolClassOperUpStreamLuDefs,
dspuPoolClassOperDnStreamLuDefs
}STATUScurrentDESCRIPTION"LU pool class information"::={ ciscoDspuMIBGroups 2}dspuPooledLuGroup OBJECT-GROUP
OBJECTS{ dspuPooledLuPeerPuIndex,
dspuPooledLuPeerLuLocalAddress
}STATUScurrentDESCRIPTION"Pooled LU information"::={ ciscoDspuMIBGroups 3}dspuPuGroup OBJECT-GROUPOBJECTS{ dspuPuAdminName,
dspuPuAdminType,
dspuPuAdminRemoteMacAddress,
dspuPuAdminRemoteSapAddress,
dspuPuAdminLocalSapAddress,
dspuPuAdminXid,
dspuPuAdminXidFmt,
dspuPuAdminWindowSize,
dspuPuAdminMaxIframe,
dspuPuAdminLinkRetryCount,
dspuPuAdminLinkRetryTimeout,
dspuPuAdminStartPu,
dspuPuAdminDlcType,
dspuPuAdminDlcUnit,
dspuPuAdminDlcPort,
dspuPuAdminFocalPoint,
dspuPuAdminRowStatus,
dspuPuOperName,
dspuPuOperType,
dspuPuOperRemoteMacAddress,
dspuPuOperRemoteSapAddress,
dspuPuOperLocalSapAddress,
dspuPuOperXid,
dspuPuOperXidFmt,
dspuPuOperWindowSize,
dspuPuOperMaxIframe,
dspuPuOperLinkRetryCount,
dspuPuOperLinkRetryTimeout,
dspuPuOperStartPu,
dspuPuOperDlcType,
dspuPuOperDlcUnit,
dspuPuOperDlcPort,
dspuPuOperFocalPoint,
dspuPuOperState,
dspuPuOperFsmState,
dspuPuOperStartTime,
dspuPuOperLastStateChgTime,
dspuPuStatsSentBytes,
dspuPuStatsRcvdBytes,
dspuPuStatsSentFrames,
dspuPuStatsRcvdFrames,
dspuPuStatsSentNegativeRsps,
dspuPuStatsRcvdNegativeRsps,
dspuPuStatsActiveLus,
dspuPuStatsInactiveLus,
dspuPuStatsBindLus,
dspuPuStatsActivationFailures,
dspuPuStatsLastActivationFailureReason
}STATUSobsolete-- superseded by dspuPuGroupV11R01DESCRIPTION"Upstream/Downstream PU node information"::={ ciscoDspuMIBGroups 4}dspuLuGroup OBJECT-GROUPOBJECTS{ dspuLuAdminType,
dspuLuAdminPoolClassName,
dspuLuAdminPeerPuIndex,
dspuLuAdminPeerLuLocalAddress,
dspuLuAdminRowStatus,
dspuLuOperType,
dspuLuOperPoolClassName,
dspuLuOperPeerPuIndex,
dspuLuOperPeerLuLocalAddress,
dspuLuOperState,
dspuLuOperFsmState,
dspuLuOperSessionState
}
STATUSobsolete-- superseded by dspuLuGroupV11R01DESCRIPTION"Upstream/Downstream LU information"::={ ciscoDspuMIBGroups 5}dspuSapGroup OBJECT-GROUPOBJECTS{ dspuSapType,
dspuSapOperState,
dspuSapRowStatus
}STATUScurrentDESCRIPTION"Local SAP information"::={ ciscoDspuMIBGroups 6}dspuPuGroupV11R01 OBJECT-GROUPOBJECTS{ dspuPuAdminName,
dspuPuAdminType,
dspuPuAdminRemoteMacAddress,
dspuPuAdminRemoteSapAddress,
dspuPuAdminLocalSapAddress,
dspuPuAdminXid,
dspuPuAdminXidFmt,
dspuPuAdminWindowSize,
dspuPuAdminMaxIframe,
dspuPuAdminLinkRetryCount,
dspuPuAdminLinkRetryTimeout,
dspuPuAdminStartPu,
dspuPuAdminDlcType,
dspuPuAdminDlcUnit,
dspuPuAdminDlcPort,
dspuPuAdminFocalPoint,
dspuPuAdminRowStatus,
dspuPuAdminRemoteAddress,
dspuPuOperName,
dspuPuOperType,
dspuPuOperRemoteMacAddress,
dspuPuOperRemoteSapAddress,
dspuPuOperLocalSapAddress,
dspuPuOperXid,
dspuPuOperXidFmt,
dspuPuOperWindowSize,
dspuPuOperMaxIframe,
dspuPuOperLinkRetryCount,
dspuPuOperLinkRetryTimeout,
dspuPuOperStartPu,
dspuPuOperDlcType,
dspuPuOperDlcUnit,
dspuPuOperDlcPort,
dspuPuOperFocalPoint,
dspuPuOperState,
dspuPuOperFsmState,
dspuPuOperStartTime,
dspuPuOperLastStateChgTime,
dspuPuOperRemoteAddress,
dspuPuStatsSentBytes,
dspuPuStatsRcvdBytes,
dspuPuStatsSentFrames,
dspuPuStatsRcvdFrames,
dspuPuStatsSentNegativeRsps,
dspuPuStatsRcvdNegativeRsps,
dspuPuStatsActiveLus,
dspuPuStatsInactiveLus,
dspuPuStatsBindLus,
dspuPuStatsActivationFailures,
dspuPuStatsLastActivationFailureReason
}STATUScurrentDESCRIPTION"Upstream/Downstream PU node information"::={ ciscoDspuMIBGroups 7}dspuLuGroupV11R01 OBJECT-GROUPOBJECTS{ dspuLuAdminType,
dspuLuAdminPoolClassName,
dspuLuAdminPeerPuIndex,
dspuLuAdminPeerLuLocalAddress,
dspuLuAdminRowStatus,
dspuLuOperType,
dspuLuOperPoolClassName,
dspuLuOperPeerPuIndex,
dspuLuOperPeerLuLocalAddress,
dspuLuOperState,
dspuLuOperFsmState,
dspuLuOperSessionState,
dspuLuOperLastActivationFailureReason
}STATUScurrentDESCRIPTION"Upstream/Downstream LU information"::={ ciscoDspuMIBGroups 8}-- end of conformanceEND